ettekirjutuse nr 7.2-6.4/106 punkti 3 osaline täitmine

Saatja: Irina Belik <[email protected]>

Saadetud: 20.02.2020 13:41

Adressaat: PÄA Ida <[email protected]>

Teema: ettekirjutuse nr 7.2-6.4/106 punkti 3 osaline täitmine

Manused: MOTIVO KLARLACK 2080.pdf

From: Disainstuudio Avers <[email protected]> Sent: Wednesday, February 19, 2020 5:59 PM To: Inna Popova <[email protected]>; Irina Belik <[email protected]> Subject: сертификат на доски Liivarand Spa

Добрый день! Ирина после нашего телефонного разговора высылаю данные, что мы

получили)

Сертификат от нашего поставщика, изначально все доски были заказаны

с Латвии, там же их и и готовили в размер, красили и обрабатывали:

Motivo klarlack огнезащитным средством (сертификат в приложении)

Ирина, если возможно пришли ссылку на сайт-ехала в машине не смогла записать название

Спасибо! Хорошего дня!

С уважением, Марина Фомина 5099427 Дизайн Студия Аверс руководитель студии, дизайнер

Data Sheet No. 2580 Edition dated: 03.12.2018 15:50 en

MOTIVO KLARLACK 2080

Description

Product Description Clear, water-borne, quick-drying 1C top coat. Can be used as base and top coat with good grain accentuation. Non-blocking and elastic.

Raw Material Base / Binder Type / Active Agent

Polyurethane combination

Application For furniture, interiors and general carpentry work. Certificates / Label Test standard compliance for:

DIN 4102-1 B1 (low flammability) Minergie Eco compatible Gloss Level 05,15,20,30,50 Packaging Paint 5 kg, 10 kg, 25 kg

Technical Data

Technical Data Product Material Safety Data Sheet 258000 Density (20ºC) 1.029 g/cm³ Solids Content 36 ± 1 w/w-% Organic Solvent Content 2 ± 1 w/w-% VOC Content (EU) 65 g/L Shelf Life at 20°C in Unopened Original Containers

6 Months

Theoretical Coverage 100-120 g/m² → -8-10 m²/kg The data apply for: 25853000. Values can vary depending on color or gloss level.

Safety Data

Refer to the following safety data sheets as well as the instructions on the label Product 258000 - MOTIVO KLARLACK 2080-05

Application advice

Wood substrate

Product Data Sheet Applied Quantity / Layer Thickness

Stain: Stain if required Primer: MOTIVO KLARLACK 2580 2580 110 g/m2 Intermediate sanding: With grain 220-280 Recoating: Motivo Klarlack 2580 2580 110 g/m2

Teknos Feyco AG Industriestrasse 3 LI-9487 Gamprin-Bendern

T +423 375 94 00 F +423 375 94 99

[email protected] www.teknos.ch

1 / 3

Data Sheet No. 2580 Edition dated: 03.12.2018 15:50 en

For further applilcation proposals please ask our representative.

Preparation

Substrate Every substrate must be well-cleaned, dry and free from grease and oil. Untreated wood substrate Always apply the product to freshly sanded surfaces.

Wood sanding grain 180-220

Processing

Preventative Measures We recommend wearing personal protective clothing, even in cases where no local regulations are in force. CH: The precautions prescribed by SUVA with respect to hygiene and equipment must be observed.

Stir Stir product well before use.

Dilution With water if necessary.

Brush Yes, in some cases, only small parts and strips

Roller In some cases, only small parts and strips With the addition of 0.5-1.0% MOTIVO ENTSCHÄUMERS Z3952.

Trowel No

Application

Viscosity Dilution Nozzle Pressure Spray Cycles Gravity Feed Gun 30-34" DIN 4 mm 0-5 % 1.8-2 mm 2-3 bar 2

Suction Cup Gun 30-34" DIN 4 mm 0-5 % 1.8-2 mm 2-3 bar 2

Airless-(Airmix) Spray Application

30-34" DIN 4 mm

0-5 % 0.15-0.23 mm 60-80 bar (material pressu re).Atomising air pressure 1.0-1.5 bar

2

HVLP Spray Gun 30-34" DIN 4 mm 0-5 % 1.8-2 mm 2-3 bar 2

Teknos Feyco AG Industriestrasse 3 LI-9487 Gamprin-Bendern

T +423 375 94 00 F +423 375 94 99

[email protected] www.teknos.ch

2 / 3

Data Sheet No. 2580 Edition dated: 03.12.2018 15:50 en

Drying Time

Drying Time At 23°C and 65% rel. humidity Dust dry after: 30 minutes

Touch dry after: 45 minutes Sandable after: 2 hours Recoatable after: 2 hours Fully dry after: 10 days

Important Remarks

Specific Restrictions For stairs, please use MOTIVO 2585 TE

Warning: If the substrate or room temperature is high, carefully add 2-5% RETARDANT ADDITIVE Z01020 FOR WATER-BORNE COATING as necessary.

Storage Conditions Store product tightly closed between +5 and +30° C. Coating Removal Strip Equipment Cleaning Immediately after use with water, dried up material with REINIGUNGSMITTEL S V820.

This data sheet is for your reference and information only. The above data are correct to the best of our knowledge. We offer no guarantees for use and exclude any liability. This applies in particular to consequential damage. We are not liable for any advice given by our employees. Our employees give non-binding information only. Site supervision, compliance with handling regulations, and adherence to recognized engineering rules are the responsibility of the manufacturer, even if our employee was on site during handling. Modifications due to technical developments may be made. The latest version of this information is applicable. In special cases, please request separate technical specifications.

Powered by TCPDF (www.tcpdf.org)

Teknos Feyco AG Industriestrasse 3 LI-9487 Gamprin-Bendern

T +423 375 94 00 F +423 375 94 99

[email protected] www.teknos.ch

3 / 3